TouchControl 5
Metering meets Monitor Control
Meet TouchControl 5, our Dante® based AoIP monitor controller with metering.
Built on our long and proud legacy of making broadcast-ready monitor controllers, it features a 5” intuitive touchscreen and a small footprint that preserves valuable space at your desktop.
It even features RTW standard precision metering, including SPL, measured using the built-in microphone.
- Monitor Control for Dante® Audio over IP Networks
- Integrated Microphone for SPL Measurement and Talkback
- RTW Metering with Premium PPM, True Peak and VU
Up Front
On the front of TouchControl 5, the integrated microphone feeds the SPL measurement, and it can also be used for talkback. The 5” touchscreen is user configurable, as is the pushable rotary knob.
Monitor Control from Stereo to 22.2
With support for up to 32 Dante® channels in and out, TouchControl 5 can handle channel configurations from stereo to 22.2.
Monitor Control. Tried. Tested. Approved.
Tried, tested, and approved by many broadcast engineers around the world, you find the very same monitor control engine that you might know from our legacy surround monitor controllers.
The list is long, but let’s emphasize Downmix, Source A/B Compare, SPK Select, Calibrated Monitoring (using the internal microphone OR manual set), SPL Readout, Solo, Cut, Swap, Phase, Mono, Dim, Mute and Test Tone Generator.
The Speaker instrument is the core of the Monitor Control, and it supports channel formats up to 22.2, including immersive formats like 7.1.4.
The source select feature lets you toggle between sources for easy comparison.
On the output side, you can set up two speakers sets and easily switch between them or you can listen to your work with your favorite headphones using the headphones output.
Controls and meters on your monitor page
The SPL meter shows the calculated SPL value of your input signal.
You can show SPL either as a bar graph or as a number.
The downmix instrument outputs your 5.1 or 7.1 mix in stereo and mono.
The downmixed signal can be monitored on speakers or phones or routed back into the unit for metering purposes.
Each speaker can be muted or soloed, and you can turn the phase. Furthermore, the swap feature for the 5.1 surround format lets you swap speaker positions, for instance if you’d like to listen to your rear channels in your front speakers.
The talkback feature lets you talk to speakers or any destination in your Dante network.
LF Boost lets you boost your low frequencies with 10 dB.
Level Calibration
The speakers in your setup can be calibrated with regards to level, delay and EQ. The support for measurement microphones, the built-in test tone generator and the live-input SPL meter is the optimal tool combination for calibrating your speaker levels to ensure they are perfectly aligned.
Loudspeaker DSP Section
Each speaker has a DSP section for ultimate control. You can set individual delay, gain and phase, and a 4-band EQ is available for each speaker in your setup.
Calibrated speaker levels can easily be recalled by the press of a knob.
Bass Management
Up to two LFE channels with adjustable crossover frequencies can be adapted to your requirements using the bass management. Full-range speakers and smaller speakers can be finely tuned to each other and operated in the same system, while HP filters for bass-controlled speakers, all-pass filters for other speakers and an additional SUB output channel for formats without LFE are also available.
RTW Metering inside
As you know, metering plays a significant role in any RTW device, and so it does in the TouchControl 5.
The PPM metering engine is taken from our high-end TouchMonitor meters, and you get a wealth of ways to tailor your own metering experience, including scales, color settings and more.
True Peak metering is of course part of the metering story, as well as VU and ‘British PPM’.
Basic 4-Channel PPM and TruePeak Meter
Beside the level control fader instrument, TouchControl 5 also comes with a basic PPM meter for reliable measurement of any Dante® channel.
Beside PPM, there is a correlation indicator that helps identifying stereo correlation problems.
The switchable peak hold indicator, peak memory and over indicator complete the functionality.
PPM
TouchControl 5 supports all the different scale types need for a professional production environment.
TP20: +3..-30 dB
Dig60: 0..-60 dB
Dig40: +20..-40 dB
Dig20: 0..-20 dB
Dig0: 18..0 dB
Dig18: +18..-18 dB
ARD9: +9..-60 dB
DIN5, +5..-50 dB
DIN10: +10..-50 dB
Nordic: +12..-42 dB
BRIIa: 7..1
BRIIb: -12..+12
BRIIa ext: 7..1
BRIIb ext: -12..+12 dB
ZOOM1: +1..-1 dB
ZOOM10: +10..-10 dB
On top of the additional scales, the license features advanced settings like scale marker, DC filter, spot correlator, integration time and custom colors.
Moving Coil
The Moving Coil instrument is avilable in 2-channel stereo mode.
It provides several scales and setting options. The PPM (British) or VU displays can be shown as single or combined, vertical or horizontal instruments.
Loudness scales or a combined PPM and Loudness display (BBC mode) are also available.
Built-in Microphone for SPL or Talkback
TouchControl 5 features a built-in microphone that can be used for calibrated monitoring.
Alternatively, it can be used for intercom talkback and can address any node in the audio network .
Premium Loudness, SPL and LRA
The Loudness & SPL license expands the basic PPM instrument with graphical and numerical instruments for loudness measurements as described in current loudness guidelines (EBU R128, ITU-R BS.1770-4/1771-1, ATSC A/85, ARIB, OP-59, AGCOM, CALM, LEQ(M), TASA, SAWA).
The range of metering instruments is extended with our highly recommended LRA instrument for the graphical display of the Loudness Range.
- Full implementations of the latest loudness standards and recommendations
- Bargraphs for summed Loudness with Momentary, Shortterm, Integrated values, and Loudness Range (LRA)
- Numerical display of all relevant values like M, S, I, LRA, TPmax, Mmax, Smax, Itime
- Adds the LRA instrument
For signals with more than four channels, software license SW32001 is required.
Loudness Sum
With the Loudness Sum instrument you get a bargraph display of the summed Loudness values M, S, and/or I of a Loudness measurement acc. to EBU R128, ITU BS.1770-4/1771-1, ARIB, ATSC A/85, OP-59, AGCOM, CALM Act, LEQ(M), TASA, SAWA, or specified by customer.
A SPL meter is also included.
Loudness Num
With the Loudness Num instrument you can monitor some or all relevant values of a loudness measurement on a numerical display: M, S, I, LRA, TPmax, Mmax, Smax, Itime.
LRA (Loudness Range)
The LRA (Loudness Range) instrument displays a graphical representation of the loudness variances within short time periods.
These are measured against the Loudness Range (LRA) descriptor specified in EBU R 128.
It is used to show whether a program has a continuously constant loudness or a high variation between low and high level components.
It allows for making assumptions on whether the program has seen or requires dynamic processing with regard to the intended distribution path.
Network Level Control with Fader Instrument
The Fader instrument allows level control of any Dante® channel in your network, and you can freely configure each fader to control the number of channels you wish.
More faders can be combined, so you can control multiple groups of channels, and if you do so, levels are controlled relatively, using TouchControl 5's knob.
TouchControl 5's touch screen can of course also be used to control each fader.
You can create faders with surround- or immersive formats or single channels up to 32 channels.
Faders can be based on any of the support channel formats. Here you see a 7.1.4 and a stereo.
Examples of different fader groups: mono, stereo or 4-channel. The basic version can monitor up to 4 channels, but can be expanded to 32 channels with the multichannel license (SW32001).
Design Your Own View Pages
TouchControl 5 lets you design your own view pages.
For each instrument you can decide on size, ratio and placement, and several instruments can be rotated to fit your needs.
Buttons can be placed anywhere on the screen, those that are placed in the side bar are avaiable across view pages.
Say you want your input selector to be avilable also on the metering page - just place it in the side bar.
To allow for more space for instruments, the side bar can be hidden.
Extensive Routing
The Routing page lets you route your audio channels to and from TouchControl 5.
With support for 32 Dante® channels plus the physical I/Os, there is a lot of possibilities.
Built for Dante® Audio over IP networks
TouchControl 5 is built for Dante® Audio over IP networks.
It supports 32 channels in and out, up to 96 kHz.
Plugged In
TouchControl 5 is born and raised as a network device. Therefore, it does not need many connections to the outside world, which is how we have been able to build a device with a very small footprint.
The network port not only provides the audio channels, 32 in and 32 out, but also includes power. On top of that, you’ll also find a pristine 24 bit/96 kHz IO section.
Easy Setup with Web-based Interface
Being a true network device, the setup of TouchControl 5 is done through the network, using a standard web browser.
This is where you make the overall settings, manage presets, handle licenses and more.
You can also control the access to the device, including limiting operation to only certain features, avoiding un-intentional use during showtime.
Monitoring Controller in a New Shape
Watch our TouchControl 5 video
Built on the Power of RTW Legacy
TouchControl 5 is built on our long and proud history of making high-end monitoring controllers. Many SurroundControl 31900 and 31960’s are still in use at large broadcast stations around the world.
On the outside, you can clearly see the similarities when comparing with the 30050 Remote Control.
On the inside, you will find even more similarities, as the monitoring engine of TouchControl 5 is built on the monitoring engine from 31900.
TouchControl 5 (2024) and Remote Control 30050 (2004)
SurroundControl 31900
Key Features
- Level Control of up to 24 (32) Audio Channels.
- User Configurable 5” Touch Display.
- Integrated Microphone for Talkback and SPL Measurement.
- Studio Grade Microphone Input: 48 V Phantom Powered High-quality Microphone Input (XLR).
- Level Control with User Definable Key Functions: The level control encoder is used to control the level of selected audio channels. It can be pressed for mute or dim.
- Powerful Headphone Output: 1/4 inch Headphone output with the option of monitoring a user-defined downmix.
- Analog Speaker Output: 3.5mm speaker output with the option of monitoring a user defined downmix.
- 24 (32) Channels Level Metering: Up to 32 in various configurations channels can be metered.
- Easy Setup with Web-based Interface.
- Dante® Audio over IP Networks.
- Calibrated Monitoring using internal microphone or manual set.
- Power over Ethernet: One cable for both audio and power (IEEE 802.3af compliant).
- Supports 16/24/32 bit and 44.1/48/88.2/96 kHz sample rate.
- License structure that allows for attractive pricing.
- Lockable Operation Mode: Fool-proof setup with access only to relevant controls. Prevents unintentional operation during showtime.
- Different versions: Table-top unit with basic equipment (order no. 320517ND) or preconfigured model with Multichannel and Monitoring licenses (order no. 320517ND + SW32001 + SW32010).
Software Licenses
The TouchControl 5 feature set is based on licenses installed, and the basic software gives you level control and PPM metering of up to 4 channels.
Software licenses expand this feature set with options for Multichannel, Monitor Control, Loudness and more.
Accessories
Ethernet Power Injector
Many ethernet switches provide Power over Ethernet (PoE), so in many cases, an additional power supply (ethernet power injector) is not needed for TouchControl 5.
In cases where you do need it, we offer the Power Injector with mains cable for different regions.
Europe or similar: Order number 14554-EU
US or similar: Order number 14554-US
Australia or similar: Order number 14554-AU
UK or similar: Order number 14554-GB
International (all cables): Order number 14554-IN
1166 - Metal Mounting Plate
Using the mounting plate, TouchControl 5 can be mounted on a mic stand or similar (3/8").